GM Models Ignition Tip

With a little patience and practice, any locksmith technician, beginner or not, can remove a mid 90's GM ignition cylinders without investing in some of the drill rigs or pick sets that are offered by many vendors in order to get the job done. In order to do so, I have composed a simple process involve few easy steps. First, the trim ring or bezel would have to be removed from around the ignition cylinder. This ring should come off fairly easy with just a little praying. Next step would be to remove the Torx screws that hold the bottom of the shroud on and then swing it off of the rear clips. At the 9 o'clock position when looking at the key-way there will be a small gap visible. Using an old pick or piece of spring steel, slide it into the gap. This will be used as a tension tool in order to put pressure of the lock's sidebar.

Now rake the wafers with a pick while putting tension on the sidebar. It is something that can be felt once the sidebar is depresses all the way. Now use a small screw driver in the key-way to begin turning the switch to the "On" position. While this is done the "tension" tool would have to be removed. Finally, either the upper shroud can be removed in order to depress the retainer and free the lock for making a key, or a tool such as Tech Train's cylinder retainer depressing tool can be used to do that as well. The code is stamped on the lock cylinder and should be visible. Once the first key is made, replace everything back and snap the trim ring as well over the face of the ignition. With a little practice, this job can be done in 15- 20 minutes.

Visit the following links for additional information about locksmith services in Portland, OR | Portland locksmith solutions.

Automotive Broken Key Extraction in Portland, OR

See full list on Listly

Finding The Right Solution

I remember a time once I was a terribly embarrassed while I was facing with a technical locksmith dilemma. There was a deadbolt lock on a school supply room and key-in-knob lock, as well. The school engineer, with a large set of keys, and the school custodian were trying to open the supply room door for materials that were needed immediately. The principal was out of the building at the time, but she did left them with her set of  keys of the school to open the door. They were able to open the key-in-the knob lock, but could not find the key for the deadbolt.

Since I was a teacher at the school, they called me, knowing I was a professional locksmith as well. When I got there, the engineer and custodian filled me in on the situation and the fact that they had tried every key on both sets (the principal's and the school engineer) several times, but without any luck, except for the bottom key-in-knob lock they opened successfully. The engineer showed me that he tried removing the molding, but could not access the lock itself. He consulted me about drilling through the deadbolt cylinder. Due to the nature of the situation, it seemed reasonable to do so.

So, I showed him the point at which to drill. He got his drill out and he was about to begin drilling when the principal suddenly showed up earlier than expected. The engineer and custodian approached her and explained to her the situation and the fact that they couldn't find the key for the other lock. Her response was that "The same key opens both locks." Apparently, it might have been a good idea to try that same key on both locks to avoid all the hassle and unnecessary embarrassment.

Visit the following links for more information about locksmith services in Portland, Oregon | Locksmith solutions in Portland, Oregon.

Commercial Locksmith Service in Portland

See full list on Listly

Premier NorthWest Locksmith Listly Page

See full list on Listly

Thumbtak Business Page

Premier NorthWest Locksmith Portland

by Premier NorthWest Locksmith Portland

Premier NorthWest Locksmith Portland a company locally owned and operated in the Portland area to provide services for its residents. With many years in the field, we are proud to offer variety of...

Questions? Comments? Requests? Get in touch.

Contact Now

Brought to you by 

Schlage Wafer Lock

The Schlage wafer lock works somewhat in a different way than other locks some of you locksmith

technicians have experienced in the past. The wafer lock by Schlage concept is nothing new. The Schlage began developing and marketing this design in 1927. Most of the wafer locks some of you locksmith technicians have seen up to now were limited by the number of possible key changes and the methods that had to be used in order to accomplish master and grand master keying.

The Schlage Wafer design is capable of  1120 key changes, and can be master and grand master keyed. A master key can control a maximum 480 key changes. These locks can be found in apartment buildings and private homes across the country. Because of their heavy duty design, it is most likely these locks would need to be services by a professional locksmith from time to time.

The most common service for this type of lock is a simple re-key, or changing the lock cylinder so that the old key will no longer work with the lock. The other type of service might be to make a key for the lock since the older key was probably lost. Very rarely, customers will call to get these lock recombined to be part of a master-key system. However, master-key system require high skills and experience to implement, and the principle of it would have to be learned carefully.

Visit the following link for similar locksmith services in Portland, OR | Locksmith solutions in Portland.